Tang fragment of a knife HR-6246
Marianne. Senn (Empa, Dübendorf, Zurich, Switzerland) & Christian. Degrigny (HE-Arc CR, Neuchâtel, Neuchâtel, Switzerland) & Naima. Gutknecht (HE-Arc CR, Neuchâtel, Neuchâtel, Switzerland) & Rémy. Léopold (HE-Arc CR, Neuchâtel, Neuchâtel, Switzerland)
Tang fragment of a knife with shiny yellow and green-blue corrosion products (Figs. 1 & 2). Dimensions: L = 2.7cm; Ø = around 5mm; WT = 5.8g.
Household implement
Hauterive - Champréveyres, Neuchâtel, Neuchâtel, Switzerland
Excavation 1983-1985, object from layer 1 (layer with material from Bronze Age till 20th cent.)
Late Bronze Age
Hallstatt A/B
Lake
Laténium, Neuchâtel, Neuchâtel
Laténium, Neuchâtel, Neuchâtel
Hr 6246
N/A
The object was sampled in 1987 for analysis. Documentation of the strata in binocular mode on the remaining fragment of the object was performed in 2022.
The schematic representation below gives an overview of the corrosion structure encountered on the tang from a first visual macroscopic observation.
Strata | Type of stratum | Principal characteristics |
CP1 |
Corrosion product |
Nodule, light brown, thin, scattered, compact, severable, very soft |
CP2 | Corrosion product | Dark green, submetallic, thin, scattered, compact, tough, soft |
CP3 | Corrosion product | Blue, submetallic, thin, scattered, compact, tough, soft |
CP4 | Corrosion product | Black, resinous, thin, discontinuous, compact, malleable, very soft |
CP5 | Corrosion product | Yellow, metallic, medium (thickness), discontinuous, compact, brittle, hard |
CP6 | Corrosion product | Red, adamantine, thin, continuous, non-compact, friable, soft |
CP7 | Corrosion product | Light brown, matte, thin, continuous, compact, friable, soft |
CP8 | Corrosion product | Light yellow, matte, thin, continuous, non-compact, powdery, very soft |
M1 | Metal | Yellow, thick, metallic, soft |
Table 1: Description of the principal characteristics of the strata as observed under binocular and described according to Bertholon's method.
The cross-section corresponds to a lateral cut (Fig. 3). The surface is covered with a thick corrosion layer but part of it has gone (Fig. 7).
Tin Bronze
Cold worked with partial annealing
MAH 87-197
Musées d'art et d'histoire, Genève, Geneva
Musées d'art et d'histoire, Genève, Geneva
1987, metallography and corrosion characterisation
This sample is mentioned in Schweizer, 1994.
Analyses performed:
Non-invasive approach
XRF with handheld portable X-ray fluorescence spectrometer (NITON XL5). General Metal mode, acquisition time 60s (filters: Li20/Lo20/M20).
Invasive approach (on the sample)
Metallography (etched with ferric chloride reagent), Vickers hardness testing, ICP-OES (conditions provided in the About tab of the MiCorr application), SEM/EDS (20keV, Microcity), XRD.
XRF analyses of the tang fragment were carried out on two representative areas (Fig. 3). Point 1 was done in a lacuna of the green-blue corrosion layer, while point 2 was performed on a black corrosion layer (CP4) where all strata (soil, corrosion products, and metal) are analyzed at the same time.
The metal is presumably a tin bronze alloy. The other elements detected are : S, Si, Pb, Sb, Fe, As, Ni, Ag, Zn, Co.
Both results are similar.
Elements (mass %) |
Cu |
Sn |
S |
Si |
Pb |
Sb |
Fe |
As |
Ni |
Ag |
Zn |
Co |
|
||||||||||||
|
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
% |
+/- 2σ |
Total |
1 |
83.0 |
0.1 |
10.0 |
0.05 |
2.5 |
0.03 |
1.5 |
0.05 |
0.5 |
0.02 |
0.5 |
0.02 |
0.4 |
0.02 |
0.4 |
0.03 |
0.3 |
0.01 |
0.2 |
0.01 |
0.1 |
0.02 |
<0.1 |
0.01 |
99.4 |
2 |
81.0 |
0.2 |
9.0 |
0.06 |
2.0 |
0.04 |
0.7 |
0.09 |
0.7 |
0.02 |
0.7 |
0.02 |
0.5 |
0.02 |
1.0 |
0.03 |
0.3 |
0.02 |
0.3 |
0.01 |
0.1 |
0.03 |
<0.1 |
0.01 |
99.3 |
Table 2: Chemical composition of the surface of the tang at two representative areas shown in Fig. 3. Method of analysis: XRF, UR-Arc CR.
The remaining metal is a tin bronze (Table 3) with high porosity (Figs. 7-9) and large cracks both on the left and right edges of the sample (Fig. 9). The metal contains small, elongated copper sulphide (Table 4) and Pb inclusions. The etched metal shows three zones with a core where elongated grains and slip lines are visible indicating cold working without annealing (Figs. 9-10), while annealing appears on both external sides (Fig. 9-11). The average hardness of the metal is HV1 145, but significant variations are observed, depending on where the measurements are taken.
Elements | Cu | Sn | Sb | Ni | Pb | As | Ag | Co | Fe | Zn |
---|---|---|---|---|---|---|---|---|---|---|
mass% | 89.85 | 8.02 | 0.60 | 0.55 | 0.34 | 0.34 | 0.18 | 0.10 | 0.02 | 0.01 |
Table 3: Chemical composition of the metal. Method of analysis: ICP-OES, Laboratory of Analytical Chemistry, Empa.
Elements | O | S | Cu | Total |
---|---|---|---|---|
mass% | 0.9 | 20 | 77 | 98 |
Table 4: Chemical composition of inclusions. Method of analysis: SEM/EDS, Laboratory of Analytical Chemistry, Empa.
Mixture of elongated grains with slip lines and polygonal grains with twin lines
Cu
Co, Ni, As, Ag, Sn, Sb, Pb
Schweizer (1994) indicates that the copper-tin alloys similar to the one of the tang have minor constituents that were certainly not added intentionally. Furthermore, he mentions that there is no systematic composition difference between bronzes with a lake patina and those with a land patina.
The corrosion layer has a thickness between 130µm and 70µm (Fig. 12). The observation of the sample in cross-section (Figs. 12-13) shows the presence of a succession of layers : S1 sediment, at the very top surface; CP1 thick continuous layer, dark grey in bright field, dark turquoise in dark field; CP2 thin continuous layer which might expand through the whole CP1, extra light grey in bright field, black in dark field; CP3 thin continuous layer, extra light grey in bright field, light brown in dark field; CP4 medium discontinuous layer, dark grey in bright field, light green in dark field; CP5 medium continuous layer, light grey in bright field, dark orange in dark field; CP6 thin discontinuous layer, black in bright field, light brown in dark field; CM1 medium discontinuous layer;
The elemental chemical distribution (Fig. 15) of the SEM image (Fig. 14) of the visually identified strata by cross-sectional observation shows that :
S1 has Ca, Al, Si and O elements;
CP1 stratum contains Cu, O and S;
CP2 stratum contains Cu, S and Fe;
CP3 stratum contains Sn, Fe and S;
CP4 stratum contains Sn and O;
CP5 stratum contains Cu, O and S;
CP6 stratum contains Sn and O, similar to CP4;
XRD analyses indicated the presence of posnjakite/Cu4SO4(OH)6H2O, chalcocite/CuS and djurleïte/Cu1.93S (Schweizer 1994).
Uniform - transgranular
Type I (Robbiola)
None.
The following correspondence can be found: CP1 in binocular mode as sediment (S1) in cross-section mode. CP2 and CP3 in binocular mode are differentiated by their color. They match CP1 in cross-section mode. CP4 in binocular mode matches CP2 in cross-section mode. CP5 in binocular mode seems to match CP3 in cross-section mode. CP6 and CP7 in binocular mode match CP4 in cross-section mode. CP8 in binocular mode matches CP5, CP6 and CM1 in cross-section mode.
On cross-section, it was possible to describe and analyze the microstructure of the metal.
The tang fragment is made from a tin bronze and has been cold worked with partial annealing since slip lines are still visible. Past XRD analyses indicate the presence of chalcopyrite in the corrosion layer, typical of lake context (Schweizer 1994), which we seem to have found locally in the corrosion structure. This object was certainly abandoned rather quickly in an anaerobic, humid and S and Fe-rich environment, favouring then the formation of chalcopyrite, before being exposed in an aerated environment in which the corrosion structure was formed. The limit of the original surface most probably lies between the Sn-rich inner layer and the Fe/Cu and S-rich outer layers. The corrosion is a type 1 according Robbiola et al. 1998.
This object was first sampled in 1987. Thanks to an extensive documentation on the cross-section and comparison with similar objects (see references), Schweizer defines a "land patina" typology on this object.
References on object and sample
Object files in MiCorr
1. MiCorr_Pin or needle fragment HR-3031
2. MiCorr_Tang fragment of a knife HR-6567
3. MiCorr_Pin HR-17773
4. MiCorr_Pin HR-3071
5. MiCorr_Pin HR-18603
6. MiCorr_Pin HR-3389
7. MiCorr_Pin HR-18152
References object
8. Rychner-Faraggi A-M. (1993) Hauterive – Champréveyres 9. Métal et parure au Bronze final. Archéologie neuchâteloise, 17 (Neuchâtel).
References sample
9. Rapport d'examen, Laboratoire Musées d'art et d'histoire, Geneva GE (1987), 87-194 à 197.
10. Schwartz, G.M. (1934) Paragenesis of oxidised ores of copper, Economic Geology, 29, 55-75.
11. Schweizer, F. (1994) Bronze objects from Lake sites: from patina to bibliography. In: Ancient and historic metals, conservation and scientific research (eds. Scott, D.A., Podany, J. and Considine B.B.), The Getty Conservation Institute, 33-50.
References on analytic methods and interpretation
12. Robbiola, L., Blengino, J-M., Fiaud, C. (1998) Morphology and mechanisms of formation of natural patinas on archaeological Cu-Sn alloys, Corrosion Science, 40, 12, 2083-2111.